![]() ![]() PID hash table entries: 128 (order: -3, 512 bytes) Kernel command line: board=TL-MR3040-v2 console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd Built 1 zonelists in Zone order, mobility grouping on. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Initrd not found or empty - disabling initrd I finally ended up using ssh 192.168.1.1 connect into the box and first thing I do is check dmesg.ĭont you think my dmesg is looking good ? the following is below Everytime I try to connect it showed something like "Voided where week signal" but in fact the signal is very strong because the 3040 just few feets away from me.Īnd I also try to use the WUI to connect 192.168.1.1 and never go through. Hope you are not consider me as a spammer.Īlright! I finally managed to get it up and running after several days truggle with the 3040 but still not be able to connect to AP name "Piratebox - share Freely" even thought it appeared on my APs list. I did create multiple accounts by the time to urgent post this question. Last edit at 05:34AM by rhydina.įirst of all I am apologize for not using the same nick because I cant remember the password of that username. Would that help and how would I bridge a connection to allow that? I'd need to use a router or switch instead of a direct to PC connection, right?Įdited 5 time(s). I read another topic that recommended using wget from the unit itself into the /tmp folder and to flash from there - but I don't have internet connectivity. This shouldn't be a brick if I can still telnet in, right? Do I need to change from WISP to another mode for the SSID to broadcast? My HTTP isn't redirecting to the web portal when hardlined to the modem, either.Įdit 2: just realized the beta stuff is old.still, the stable release is giving me this issue. Last light on modem stays solid red, third occassionally blinks green and first stays solid green. BIN from telnet, or does it not matter - if so, do I need the beta version?Įdit: flashed with the beta install folder in my root through Putty over telnet, still no BSSID broadcasting. What else can I try from here? Does it matter that the unit was initially set up with pirate box setup files from /auto/install_piratebox.zip instead of /auto/install_piratebox.zip, or are the checksums the same? Do I still need the setup files (install folder) on the mass storage device when flashing another. I'm not really sure what else I'm missing. The first light on the modem is blinking and the second and fourth lights stay solid. Īnd my USB storage device has a steady blink. bin on cdsmythe's tutorial ( ) with the unit in WISP mode this time - Putty says I've since did a telnet back in using Putty and attempted to flash using the. bin on and ran into issues where I could telnet, but would get insufficient space messages on nearly every command - my SSID also would not broadcast. Perhaps you should write "USB storage", or "USB stick".Įdited 3 time(s). It was a bit confused: do I have to connect the TP-Link USB cable ? (I'm a newbie with this kind of device). ![]() "Shutdown the Piratebox and connect the USB to your computer.Ĭopy files from your computer to the USB, placing them in the folder -" After the update process the new IP address of the Piratebox will be 192.168.1.1 – change your computer settings so you have an IP address of 192.168.1.2 subnet 255.255.255.0 so you can continue to connect with the MR3040 using Terminal or PuTTY." I did not this (by lazyness) and however it worked (OS used: Xubuntu 12.04). I did not (all copied at / ), and my PirateBox installation did not work (no PirateBox WIFI SSID viewable). You should add the instruction to extract by keeping the "/install" directory on the USB stick. Extract the install_piratebox.zip file to your usb stick" One with the original name, ad second time renamed as "openwrt.bin" If I remember well what I did, I copied the file "openwrt-ar71xx-generic-tl-mr3040-v2-squashfs-factory.bin" 2 times onto the USB stick. Where to get this file ? If this step necessary ? (as we will flash the router with a file toke from the computer). However I have some comments to help next people to do it a bit more easier: I have successfully installed PirateBox 1.0beta onto a MR3040 v2.3 following the cdsmythe's tutorial. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |